Actron Elite AutoScanner® CP9185 User Manual Page 134
- Page / 240
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Ford Historic (OBD I) Diagnostics
6 – 12 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
6
Computed Timing Check (1984-1991 EEC-IV Vehicles)
✓ This option of the KOER Read Codes function allows you to check
both the Base engine timing (no computer adjustment) and the
ability of the computer to control spark advance.
✓ This does not apply to 7.3L diesel vehicles.
✓ Connect a timing light to the vehicle in accordance with the
manufacturer’s instructions. (For 2.3L dual plug engines, use
exhaust side plug. Refer to ignition system section in the service
manual for specific instructions.)
From the Select Code Type menu:
1. Select Computed Timing.
• Use the
UP
or
DOWN
arrow keys until Computed
Timing is highlighted.
• Press
ENTER.
✓ Perform the following
step-by-step. Failure to perform
these steps may set a false DTC in
the PCM — observe the display.
Avoid cooling fan! It may turn on during test.
1) Set parking brake.
2) Transmission in park (P) or neutral (N).
3) Turn A/C off.
4) Start engine and let idle until hot.
5) Turn ignition key off.
6) Wait 10 seconds. start engine and let Idle.
7) If vehicle is equipped with manual transmission, release clutch.
Fast Codes
Slow Codes
Computed Timing
Select Code Type
Computed Timing
!
CAUTION
- Elite AutoScanner 1
- Scan Tool Information 2
- Table of Contents 3
- Type Styles Used: 8
- Icons used: 8
- Important Safety Messages 9
- Safety Precautions 10
- Safety Precautions 11
- Section 1 – Using This Manual 17
- Using This Manual 18
- Section 2 – Getting Started 19
- Using the CD 20
- Getting Started 21
- Vehicle Service Information 22
- Other Manuals 23
- Repair Information Programs 23
- Suitable Manual Titles 23
- Getting Started 24
- SAE Publications 25
- Ford On-Board Diagnostics 26
- Data Link Connector (DLC) 27
- Ford Historic 28
- Cable Adapter 29
- Vehicle DLC 29
- GM Historic 31
- Chrysler Historic 32
- P 0 1 0 1 33
- The Scan Tool 35
- Specifications 36
- Accessories for the Scan Tool 37
- Using The Scan Tool 38
- ❒ Press and hold 39
- ✓ Each time the Scan Tool is 40
- Scan Tool Power UP 41
- System Setup 41
- Changing Measurement Units 42
- Changing Display Contrast 43
- Changing Auto-Power Off 45
- View Tool Information 46
- Display Test 47
- BACK Key 48
- Keyboard Test 49
- Memory Test 49
- ❒ Memory Test may take 50
- ❒ If no problems were 50
- Connecting The Scan Tool 51
- Review Data 52
- Playback 53
- Print Data 55
- Code Lookup 57
- LEFT or RIGHT 58
- BACK again to return to menu 59
- Setup User Key 60
- Vehicle Selection 61
- ENTER on the Scan 63
- ❒ A new vehicle is selected 65
- Global Function List 66
- ✓ View data can be shown as: 68
- Global OBD II Diagnostics 69
- BACK key to 72
- ❒ Record memory is full 75
- ❒ Operator presses 75
- Pending Codes 78
- Read Codes” on page 4-12 for 79
- View Freeze Data 82
- I/M Readiness 84
- ✓ Clear Monitors by: 87
- ✓ The Scan Tool display is 89
- State OBD Check 90
- O2 Monitor Test 91
- ✓ The O2 sensors located 93
- Diagnostic Monitor Tests 94
- ✓ On CAN vehicles Scan Tool 96
- On-Board Systems 97
- Vehicle Info 98
- BACK or ENTER key 100
- Modules Present 101
- Global OBD II Diagnostics 102
- ID Protocols 103
- $10 K2K* 103
- $1A K2K* 103
- Section 5 – GM Diagnostics 105
- Datastream Menu 106
- View Data 107
- Record Data 108
- 2.Confirm selection 109
- Diagnostic Codes Menu 110
- ✓ Perform the following: 111
- Erase Codes 112
- 1.Select Erase Codes 113
- Special Tests Menu 114
- Field Service 115
- ✓ If CHECK ENGINE light is 116
- GM Function List 118
- IMPORTANT 118
- ❒ On some GM vehicles the 121
- Section 6 – Ford Diagnostics 123
- ENTER key is pressed 127
- Read KOEO Codes 129
- ✓ Continuous memory codes 131
- ✓ Follow the instructions 132
- ❒ Work steering wheel 133
- ✓ Perform the following 134
- Only memory codes 136
- Press ENTER to cont 136
- Read KOER Codes 138
- Select IVSC Test 138
- ENTER to view the 139
- On Demand Test Menu 141
- Wiggle Test (EEC-IV Vehicles) 142
- ENTER to continue 143
- Erase Codes” on page 6-13 to 144
- Time remaining: 2:35 145
- Output Switch Test 145
- Precedure runs less 145
- than 3 minutes 145
- ENTER to continue 146
- ✓ The TEST/HOLD parameter 149
- Ford Function List 151
- ❒ Review Data 152
- ❒ Print Data 152
- System Pass 154
- No faults detected 154
- Read Codes 154
- Ford Diagnostics 156
- Chrysler Function List 157
- Tool Setup 158
- Chrysler Diagnostics 161
- Sensor Test 163
- Device Controls Menu 167
- Actuator Test 168
- Idle Speed Test 170
- IMPORT (OBD II) DIAGNOSTICS 171
- In the example shown module 174
- (MOD) $18 is reporting the 174
- • Press BACK key 174
- Section 9 – Troubleshooting 175
- Error Messages 176
- Scan Tool Does Not Power Up 176
- Vehicle Communication Fault 177
- Troubleshooting 178
- Battery Replacement 179
- Tool Self-Tests 180
- Technical Support 180
- Appendix A – PID Definitions 181
- ✓ Many diesel engines do not 182
- ✓ ENG RUN stops when engine 182
- ✓ Positive reading indicates 183
- ✓ Short-term Fuel Trim calcu 184
- ✓ Short-term Fuel Trim value 184
- PID List 185
- TELLTALE CKT Telltale Circuit 215
- Appendix B – 219
- Data Link Connectors 219
- Optional P/N 9603 221
- Available from Dealership 221
- 84-85 A/T Only 223
- Optional P/N 9605 224
- Appendix C – Glossary 227
- Glossary 228
- SOFTWARE 237
- ORDER INFORMATION 237
- Technical Service 237
- DISCLAIMER 237
- © 2006-2007 SPX Corporation 240
Related products and manuals for Tools Actron Elite AutoScanner® CP9185
(2 pages)
Tools Actron CP9110 Scan Tool User Manual
(15 pages)
(15 pages)
Tools Actron AutoAnalyzer CP7665 User Manual
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.073 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals