Actron Elite AutoScanner® CP9185 User Manual Page 97
- Page / 240
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • 4 – 33
Global OBD II Diagnostics
4
On-Board Systems
The On-Board Systems test allows the Scan Tool to control operation
of vehicle components, tests or systems.
✓ Some manufacturers do not allow tools to control vehicle systems. A
vehicle not supporting an on-board system is identified by a message
that is displayed when selected.
✓ Refer to the vehicle service manual for on-board systems instructions.
From the Special Tests Menu:
1. Select
On-Board Systems.
•Use
UP
or
DOWN
arrow
key until On-Board Systems
is highlighted.
•Press
ENTER
.
✓ A list of on-board systems and
components available for testing are shown on the display.
2. Select Test.
•Use
UP
or
DOWN
arrow
key.
•Press
ENTER
.
3. Return to On-Board Systems menu.
•Press
BACK key.
4. Return to Special Tests Menu.
•Press
BACK key.
I/M Readiness ?
Drive Cycle Monitor
State OBD Check
O2 Monitor Test
Diag Mon Tests
On-Board Systems
Vehicle Info
Special Tests Menu
On-Board Systems
Evap Leak Test
On-Board Systems
Evap Leak Test
- Elite AutoScanner 1
- Scan Tool Information 2
- Table of Contents 3
- Type Styles Used: 8
- Icons used: 8
- Important Safety Messages 9
- Safety Precautions 10
- Safety Precautions 11
- Section 1 – Using This Manual 17
- Using This Manual 18
- Section 2 – Getting Started 19
- Using the CD 20
- Getting Started 21
- Vehicle Service Information 22
- Other Manuals 23
- Repair Information Programs 23
- Suitable Manual Titles 23
- Getting Started 24
- SAE Publications 25
- Ford On-Board Diagnostics 26
- Data Link Connector (DLC) 27
- Ford Historic 28
- Cable Adapter 29
- Vehicle DLC 29
- GM Historic 31
- Chrysler Historic 32
- P 0 1 0 1 33
- The Scan Tool 35
- Specifications 36
- Accessories for the Scan Tool 37
- Using The Scan Tool 38
- ❒ Press and hold 39
- ✓ Each time the Scan Tool is 40
- Scan Tool Power UP 41
- System Setup 41
- Changing Measurement Units 42
- Changing Display Contrast 43
- Changing Auto-Power Off 45
- View Tool Information 46
- Display Test 47
- BACK Key 48
- Keyboard Test 49
- Memory Test 49
- ❒ Memory Test may take 50
- ❒ If no problems were 50
- Connecting The Scan Tool 51
- Review Data 52
- Playback 53
- Print Data 55
- Code Lookup 57
- LEFT or RIGHT 58
- BACK again to return to menu 59
- Setup User Key 60
- Vehicle Selection 61
- ENTER on the Scan 63
- ❒ A new vehicle is selected 65
- Global Function List 66
- ✓ View data can be shown as: 68
- Global OBD II Diagnostics 69
- BACK key to 72
- ❒ Record memory is full 75
- ❒ Operator presses 75
- Pending Codes 78
- Read Codes” on page 4-12 for 79
- View Freeze Data 82
- I/M Readiness 84
- ✓ Clear Monitors by: 87
- ✓ The Scan Tool display is 89
- State OBD Check 90
- O2 Monitor Test 91
- ✓ The O2 sensors located 93
- Diagnostic Monitor Tests 94
- ✓ On CAN vehicles Scan Tool 96
- On-Board Systems 97
- Vehicle Info 98
- BACK or ENTER key 100
- Modules Present 101
- Global OBD II Diagnostics 102
- ID Protocols 103
- $10 K2K* 103
- $1A K2K* 103
- Section 5 – GM Diagnostics 105
- Datastream Menu 106
- View Data 107
- Record Data 108
- 2.Confirm selection 109
- Diagnostic Codes Menu 110
- ✓ Perform the following: 111
- Erase Codes 112
- 1.Select Erase Codes 113
- Special Tests Menu 114
- Field Service 115
- ✓ If CHECK ENGINE light is 116
- GM Function List 118
- IMPORTANT 118
- ❒ On some GM vehicles the 121
- Section 6 – Ford Diagnostics 123
- ENTER key is pressed 127
- Read KOEO Codes 129
- ✓ Continuous memory codes 131
- ✓ Follow the instructions 132
- ❒ Work steering wheel 133
- ✓ Perform the following 134
- Only memory codes 136
- Press ENTER to cont 136
- Read KOER Codes 138
- Select IVSC Test 138
- ENTER to view the 139
- On Demand Test Menu 141
- Wiggle Test (EEC-IV Vehicles) 142
- ENTER to continue 143
- Erase Codes” on page 6-13 to 144
- Time remaining: 2:35 145
- Output Switch Test 145
- Precedure runs less 145
- than 3 minutes 145
- ENTER to continue 146
- ✓ The TEST/HOLD parameter 149
- Ford Function List 151
- ❒ Review Data 152
- ❒ Print Data 152
- System Pass 154
- No faults detected 154
- Read Codes 154
- Ford Diagnostics 156
- Chrysler Function List 157
- Tool Setup 158
- Chrysler Diagnostics 161
- Sensor Test 163
- Device Controls Menu 167
- Actuator Test 168
- Idle Speed Test 170
- IMPORT (OBD II) DIAGNOSTICS 171
- In the example shown module 174
- (MOD) $18 is reporting the 174
- • Press BACK key 174
- Section 9 – Troubleshooting 175
- Error Messages 176
- Scan Tool Does Not Power Up 176
- Vehicle Communication Fault 177
- Troubleshooting 178
- Battery Replacement 179
- Tool Self-Tests 180
- Technical Support 180
- Appendix A – PID Definitions 181
- ✓ Many diesel engines do not 182
- ✓ ENG RUN stops when engine 182
- ✓ Positive reading indicates 183
- ✓ Short-term Fuel Trim calcu 184
- ✓ Short-term Fuel Trim value 184
- PID List 185
- TELLTALE CKT Telltale Circuit 215
- Appendix B – 219
- Data Link Connectors 219
- Optional P/N 9603 221
- Available from Dealership 221
- 84-85 A/T Only 223
- Optional P/N 9605 224
- Appendix C – Glossary 227
- Glossary 228
- SOFTWARE 237
- ORDER INFORMATION 237
- Technical Service 237
- DISCLAIMER 237
- © 2006-2007 SPX Corporation 240
Related products and manuals for Tools Actron Elite AutoScanner® CP9185
(2 pages)
Tools Actron CP9110 Scan Tool User Manual
(15 pages)
(15 pages)
Tools Actron AutoAnalyzer CP7665 User Manual
(32 pages)
(32 pages)
© 2020, manymanuals.com. All rights reserved. | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals