Actron AutoScanner® Plus CP9580A User Manual Page 24
- Page / 126
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Getting Started
2 – 8 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
2
OBD II Diagnostic Trouble Codes
(DTCs)
✓ J2012 and ISO 15031-6 are standards for all DTCs, established by
the SAE, International Organization for Standardization (ISO) and
other governing bodies.
❒ Codes and definitions assigned by these specifications are
known as Generic OBD II codes.
❒ OBD II requires compliance to these standards for all cars, light
trucks, APVs, MPVs, and SUVs sold in the United States.
❒ Codes not reserved by the SAE are reserved for the
manufacturer and referred to as Manufacturer Specific Codes.
✓ DTCs are used to help determine the cause of a problem or
problems with a vehicle.
❒ DTCs consist of a five-digit alphanumeric code.
❒ The DTCs format and general code types are shown below.
Within each category (Powertrain, Chassis, Body and Network) of
DT
Cs there are assigned ranges for different vehicle systems.
Example:
P0101 - Mass or Volume Air Flow Circuit Range/Performance Problem
P 0 1 0 1
Vehicle Specific System
Powertrain Codes
P0xxx - Generic (SAE)
P1xxx - Manufacturer Specific
P2xxx - Generic (SAE)
P30xx-P33xx - Manufacturer Specific
P34xx-P39xx - Generic (SAE)
Chassis Codes
C0xxx - Generic (SAE)
C1xxx - Manufacturer Specific
C2xxx - Manufacturer Specific
C3xxx - Generic (SAE)
Body Codes
B0xxx - Generic (SAE)
B1xxx - Manufacturer Specific
B2xxx - Manufacturer Specific
B3xxx - Generic (SAE)
Network Communication Codes
U0xxx - Generic (SAE)
U1xxx - Manufacturer Specific
U2xxx - Manufacturer Specific
U3xxx - Generic (SAE)
Specific Fault Designation
Bx - Body
Cx - Chassis
Px - Powertrain
Ux - Network Comm.
x = 0, 1, 2 or 3
- Auto Scanner 1
- Scan Tool Information 2
- Table of Contents 3
- Section 4 – Diagnostic Menu 4
- Section 5 – Troubleshooting 4
- Type Styles Used: 6
- Icons used: 6
- Important Safety Messages 7
- Safety Precautions 10
- Safety Precautions 11
- P R N D L 2 12
- Section 1 – Using This Manual 15
- Using This Manual 16
- Section 2 – Getting Started 17
- Getting Started 18
- Vehicle Service Information 19
- Other Manuals 20
- Repair Information Programs 20
- Suitable Manual Titles 20
- Getting Started 21
- SAE Publications 22
- Data Link Connector (DLC) 23
- P 0 1 0 1 24
- The Scan Tool 25
- Specifications 26
- Using The Scan Tool 27
- ❒ Press and hold 28
- ❒ If voltage is low, the Low 28
- ❒ Replace the battery using 28
- System Setup 29
- ✓ System Setup allows: 29
- Diagnostic 29
- Connector 29
- Changing Measurement Units 30
- Changing Display Contrast 31
- Changing Auto-Power Off 31
- 15 32
- Quick Test 33
- Print Header 33
- Using The Scan Tool 34
- Language Setup 35
- Long PID Names 36
- View Tool Information 37
- Display Test 38
- Keypad Test 39
- Memory Test 39
- ✓ Memory Test may take 40
- Program Mode 41
- Review Data 42
- ✓ The Recording has frame 43
- Print Data 44
- Code Lookup 46
- Connecting The Scan Tool 48
- Vehicle Selection 48
- ❒ Global OBD II 49
- ❒ Domestic Vehicles 49
- ❒ European Vehicles 49
- ❒ Asian Vehicles 49
- ❒ Previous Vehicle 49
- ENTER on the Scan 50
- IMPORTANT 51
- ENTER to return to 55
- 56
- ❒ Code Lookup 59
- ❒ System Setup 59
- I/M Monitors (Emissions) 60
- Diagnostic Menu 61
- Diagnostic Menu 62
- Read Codes 63
- ✓ If no DTCs are present a 64
- DTC Type Description 66
- Erase Codes 68
- MIL Status 70
- State OBD Check 71
- ✓ View data can be shown as: 73
- symbol 76
- Record Data 77
- ❒ Record memory is full 79
- ❒ Operator presses 79
- ❒Refer to “Recording” for 79
- View Freeze Data 80
- ✓ Clear Monitors by: 82
- 4.Return to Diagnostic Menu 84
- BACK key 84
- O2 Monitor Tests 85
- ✓ The O2 sensors located 86
- Diagnostic Monitor Tests 88
- BACK key 90
- On-Board Systems 91
- Vehicle Information 92
- Modules Present 95
- Troubleshooting 100
- LINK ERROR 101
- Tool Self-Tests 103
- Technical Support 103
- Appendix A – PID Definitions 105
- PID Definitions 106
- PID Definitions 107
- Appendix B – Glossary 113
- Glossary 114
- Glossary 115
- Declaration of Conformity 123
- Limited Warranty 124
- © 2010 SPX Corporation 126
Related products and manuals for Tools Actron AutoScanner® Plus CP9580A
Tools Actron CP9110 Scan Tool User Manual
(15 pages)
(15 pages)
Tools Actron AutoAnalyzer CP7665 User Manual
(32 pages)
(32 pages)
Tools Actron AutoScanner® CP9575 User Manual
(16 pages)
(16 pages)
Tools Actron GM Code Scanner CP9001 User Manual
(102 pages)
(102 pages)
(26 pages)© 2020, manymanuals.com. All rights reserved. | 0.703 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals