Actron AutoScanner® Plus CP9580A User Manual Page 82
- Page / 126
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Diagnostic Menu
4 – 26 • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •
4
4
Drive Cycle Monitor
The Drive Cycle Monitor function is very similar to the I/M Monitors
though the Drive Cycle Monitor is used to view
REAL TIME operations
of the Emissions System on OBD II vehicles.
✓ Drive Cycle Monitor continuously updates as the vehicle reports
operations of the Emission System.
!
CAUTION
Two people must be in vehicle when driving. One to
drive and the other to operate the Scan Tool.
✓ Refer to the vehicle service manual for the drive cycle operation.
✓ Drive Cycle Monitor can be used if you want to drive the vehicle until
all of the monitors are OK.
✓ During normal driving conditions, the vehicle computer scans the
emission system. After a specific amount of drive time (each monitor
has specific driving conditions and time requirements), the computer
monitors will decide if the vehicle emissions system is working
correctly or not as well as detecting out a range of values. When the
monitor status is:
• “ok” - vehicle has been driven enough for function.
• “inc” (Incomplete)
- vehicle was not driven enough to complete all of
the monitors.
• “n/a” (No
t
Applicable) - vehicle does not support that monitor.
✓ Clear Monitors by:
❒ Erasing Codes.
❒ Vehicle Computer Module losing power (on some vehicles).
From the Diagnos
tic Menu:
1.
=====================
View Fre eze Data
Drive Cycle Monitor
O2 Monitor Tests
Diag Monitor Tests
On-Board Systems
Vehicle Information
Diagnostic Menu
Drive Cycle Monitor
Select Drive Cycle Monitor.
•Use
UP
or
DOWN
arrow
key to highlight Drive Cycle
M
onitors.
•Press
ENTER
.
- Auto Scanner 1
- Scan Tool Information 2
- Table of Contents 3
- Section 4 – Diagnostic Menu 4
- Section 5 – Troubleshooting 4
- Type Styles Used: 6
- Icons used: 6
- Important Safety Messages 7
- Safety Precautions 10
- Safety Precautions 11
- P R N D L 2 12
- Section 1 – Using This Manual 15
- Using This Manual 16
- Section 2 – Getting Started 17
- Getting Started 18
- Vehicle Service Information 19
- Other Manuals 20
- Repair Information Programs 20
- Suitable Manual Titles 20
- Getting Started 21
- SAE Publications 22
- Data Link Connector (DLC) 23
- P 0 1 0 1 24
- The Scan Tool 25
- Specifications 26
- Using The Scan Tool 27
- ❒ Press and hold 28
- ❒ If voltage is low, the Low 28
- ❒ Replace the battery using 28
- System Setup 29
- ✓ System Setup allows: 29
- Diagnostic 29
- Connector 29
- Changing Measurement Units 30
- Changing Display Contrast 31
- Changing Auto-Power Off 31
- 15 32
- Quick Test 33
- Print Header 33
- Using The Scan Tool 34
- Language Setup 35
- Long PID Names 36
- View Tool Information 37
- Display Test 38
- Keypad Test 39
- Memory Test 39
- ✓ Memory Test may take 40
- Program Mode 41
- Review Data 42
- ✓ The Recording has frame 43
- Print Data 44
- Code Lookup 46
- Connecting The Scan Tool 48
- Vehicle Selection 48
- ❒ Global OBD II 49
- ❒ Domestic Vehicles 49
- ❒ European Vehicles 49
- ❒ Asian Vehicles 49
- ❒ Previous Vehicle 49
- ENTER on the Scan 50
- IMPORTANT 51
- ENTER to return to 55
- 56
- ❒ Code Lookup 59
- ❒ System Setup 59
- I/M Monitors (Emissions) 60
- Diagnostic Menu 61
- Diagnostic Menu 62
- Read Codes 63
- ✓ If no DTCs are present a 64
- DTC Type Description 66
- Erase Codes 68
- MIL Status 70
- State OBD Check 71
- ✓ View data can be shown as: 73
- symbol 76
- Record Data 77
- ❒ Record memory is full 79
- ❒ Operator presses 79
- ❒Refer to “Recording” for 79
- View Freeze Data 80
- ✓ Clear Monitors by: 82
- 4.Return to Diagnostic Menu 84
- BACK key 84
- O2 Monitor Tests 85
- ✓ The O2 sensors located 86
- Diagnostic Monitor Tests 88
- BACK key 90
- On-Board Systems 91
- Vehicle Information 92
- Modules Present 95
- Troubleshooting 100
- LINK ERROR 101
- Tool Self-Tests 103
- Technical Support 103
- Appendix A – PID Definitions 105
- PID Definitions 106
- PID Definitions 107
- Appendix B – Glossary 113
- Glossary 114
- Glossary 115
- Declaration of Conformity 123
- Limited Warranty 124
- © 2010 SPX Corporation 126
Related products and manuals for Tools Actron AutoScanner® Plus CP9580A
Tools Actron CP9110 Scan Tool User Manual
(15 pages)
(15 pages)
Tools Actron AutoAnalyzer CP7665 User Manual
(32 pages)
(32 pages)
Tools Actron AutoScanner® CP9575 User Manual
(16 pages)
(16 pages)
Tools Actron GM Code Scanner CP9001 User Manual
(102 pages)
(102 pages)
(26 pages)© 2020, manymanuals.com. All rights reserved. | 1.304 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals